Beaver Valley Supply HSMSW3243

SW3243 Spreader | Same As S3243 & Has Box Main Frame Channels,Add. Supports,& Stressproof Side Shaft H&S SW3243 Spreader | Same As S3243 & Has Box Main Frame Channels,Add. Supports,& Stressproof Side Shaft Tractor Requirement – Once The Spreader Is Loaded, It Shouldn’t Weight More Than 1.5 Times The Weight Of The Tractor Unit Includes Specs Features Options Video Unit Includes Tandem Axle – 16.5 x 16.1 Floatation Tires & Rims 540 PTO 2-Speed Apron Drive 29″ Dia Beater With Replaceable Paddles Fiberglass Reinforced Plywood Sides, Front Panel, & Hyd Engate 10 Gauge Culvert Grade Galvanized Steel Side Flares Virgin Grade Bonded Poly Floor T-Rod Main Apron Chain Hyd Endgate With Cylinder(s), Hoses, & Tips. (1 Cyl On 3231 – 2 Cyls On 3237/3143/W3143) Front Splash Guard Greasable Bearings Jack Western Features Heavier- Larger Gearbox for the Beater Pole Channels have been Doubled up for added strength Boxed Main Frame Channels For Added Strength Additional Floor Supports Stress Proof Side Shaft #80 Drive chain, (Standard models have #60) All Drive Train shafts are 1045 hardened steel Additional Features A massive unitized welded frame with heavy floor supports and side stakes, wrap around steel front corners. Strong rear main beater side panels are slanted for clearance and wider spread, and then welded to the strong 5″ U channel side members compare with any on the market. The side flares on all H&S “Heavy Duty” manure spreaders are made of 10 gauge g210 culvert grade galvanized steel. Sides, front panel and both sides of the rear hydraulic end gate use fiberglass reinforced plywood to provide for easy cleaning and minimal freeze up. It also features a solid virgin grade poly floor. Considerably less torque is needed to move a heavy load. A front splash guard is standard equipment. Greaseable bearings. The two-speed apron drive is standard equipment. An optional variable speed hydraulic drive is also available. As is an optional electric control for the hydraulic drive. A 29″ diameter beater with 14 replaceable beater paddles. The beater has two types of paddles, blunt for widespread and sharp ripper type for cutting and shredding. The beater side wiper blades are also standard equipment. The hydraulic endgate features 2 cylinders as standard (optional on the 3131). The hydraulic lines are run through a 3×3 tube under the floor. The upright position of the hydraulic cylinder stroke allows the gate to lift with the least strain at pivot points. H&S uses cast special steel alloy apron idler slides instead of idler sprockets making for years of dependable service. Adjustment for the main apron is easy by simply loosening the two side bolts and drawing up the long bolt. Gear box mechanisms and drive for the beater and apron are Timken tapered roller bearing equipped. The beater drive gear box is 1-½″ bevel gear oil bath equipped with a 4-jaw over running clutch for beater shut off. The apron drive is a 50:1 bronze worm gear with shear bolt protection. The strong oil bath bevel gear box that powers the beater is tapered Timken roller bearing equipped. The gear box utilizes a 4-jaw beater shut off clutch and tractor sized spline shaft. Unloading Speed for 3131, 3137, 3143, and W3143 – (2 speed chain drive) High Speed: PTO speed 540 rpm’s 8′8.5″ per minute Low Speed: PTO speed 540 rpm’s 4′8.5″ per minute. An optional top beater is available to provide load leveling and spreading of high heaped loads. (Standard in models 3143 & W3143) The W3143 (western) has all the same features as above with additional features such as double main frame channels, additional floor supports, 1045 hardened drive shaft, #80 drive chain and a heavy duty main gear box. Unit S3123 S3127 S3231 S3237 SW3243 Capacity – Old Rating 235 bu 270 bu 310 bu 370 bu 430 bu Capacity Cu. Ft. Struck Level Per ASAE S324.2 122.04 146.35 164.58 215.68 260.59 Capacity Cu. Ft. Heaped Per ASAE S324.2 209.89 252.46 284.39 344.38 386.22 Top of Flare Width 68″ (173 cm) 68″ (173 cm) 68″ (173 cm) 68″ (173 cm) 68″ (173 cm) Inside Width 60″ (152 cm) 60″ (152 cm) 60″ (152 cm) 60″ (152 cm) 60″ (152 cm) Inside Length 11′ 4″ (3.45 m) 13′ 4″ (4.06 m) 14′ 10″ (4.52 m) 16′ (4.88 m) 16′ (4.88 m) Inside Depth 28 ⅜″ (72 cm) 28 ⅜″ (72 cm) 28 ⅜″ (72 cm) 34 ⅜″ (87 cm) 40 ⅜″ (102 cm) Overall Width w/Standard Tires 94 ½″ (240 cm) 94 ½″ (240 cm) 98″ (249 cm) 98″ (249 cm) 112″ (285 cm) Overall Length 18′ 6″ (5.7 m) 20′ 5 ½″ (6.3 m) 21′ 11 ½″ (6.7 m) 23′ 2 ½″ (7.1 m) 23′ 2 ½″ (7.1 m) Overall Loading Height-Top Of Side 51 ½″ (131 cm) 51 ½″ (131 cm) 51 ½″ (131 cm) 57 ½″ (1.5 m) 63″ (160 cm) Overall Height w/Hyd. Endgate 55″ (139.7 cm) 55″ (139.7 cm) 55″ (139.7 cm) 61″ (154.9 cm) 63 ½″ (161.3 cm) Diameter Of Beater 29″ (74 cm) 29″ (74 cm) 29″ (74 cm) 29″ (74 cm) 29″ (74 cm) Main Apron Chain T-Rod T-Rod T-Rod T-Rod T-Rod Spindle Size 2″ (5 cm) 2 ½″ (6 cm) 2 ¼″ (6 cm) 2 ½″ (6 cm) 2 ½″ (6 cm) Standard Tire Size 295 × 22.5 Recap 295 × 22.5 Recap 295 × 22.5 Recap 295 × 22.5 Recap 16.5 × 16.1 Flotation Weight w/Tires 2,890 lbs. (1,311 kg) 3,230 lbs. (1,495 kg) 4,190 lbs. (1,901 kg) 4,920 lbs. (2,232 kg) 5,500 lbs. (2,495 kg) Rear Hydraulic Endgate Standard Standard Standard Standard Standard PTO Speed 540 540 540 – Standard | 1000 – Optional 540 – Standard | 1000 – Optional 540 – Standard | 1000 – Optional Jack Standard Standard Standard Standard Standard Drive 2-Speed 2-Speed 2-Speed 2-Speed 2-Speed Front Splash Panel Standard Standard Standard Standard Standard Hyd. Cyl On Hyd. Endgate 1 – Standard | 2 – Optional 1 – Standard | 2 – Optional 1 – Standard | 2 – Optional 2 2 Upper Beater Optional Optional Optional Optional Standard 2 Speed Apron Drive Splash Guard 2nd Hyd Endgate Cyl Gearbox Apron Idler Slides Greasable Bearings Easy Cleanout Beaters Apron Adjustment Unitized Welded Frame Side Flares HSMSO310HD4 H&S Hyd Variable Speed | 4 Hose Hookup (Factory Installed) | For S3231, S3237, S3243, SW3243 $ 2,950.00 Add to List HSMSO310HD4EC H&S Hyd Variable Speed With Electric Controls | For S3231,S3237,S3243,& SW3243 | 4 Hose Hookup $ 3,538.00 Add to List HSMSOLIGHT H&S Highway Lighting Kit (Dealer Install) $ 1,265.00 Add to List HSMSOPAN310 Rear Pan (Not Installed) | For S3231, S3237, S3243, S3131, S3137, S3143, & SW3243 $ 942.00 Add to List HSMSOPNIC H&S MSOPNIC Rear Pan Installation Charge | NET PRICE $ 392.00 Add to List HSMSOWPTO1038 H&S 1-3/8 – 21 Spline – 1000 RPM PTO In Lieu Of Standard 540 PTO | For SW3243 $ 1,012.00 Add to List HSSC30000 H&S Safety Chain | 30,000 # Capacity $ 221.00 Add to List HSTWP19LS H&S (4) 19L x 16.1 10 Ply Tires With New Silver 8-Bolt Rims (Rated Tire/Rim Capacity 24,000 lbs.) $ 6,569.00 Add to List

Category: Manure Spreaders