Baumalight 3P34 Stump Grinder | 45-80 HP | CAT 2 QH-Comp | 540 RPM | 9″ Max Cut Depth Per Pass

Baumalight 3P34 Stump Grinder | 45-80 HP | CAT 2 QH-Comp | 540 RPM | 9″ Max Cut Depth Per Pass Baumalight 3P34 Stump Grinder | 45-80 HP | CAT 2 QH-Comp | 540 RPM | 9″ Max Cut Depth Per Pass PRICE DOES NOT INCLUDE SETUP OR SHIPPING – PRICED FOB BV-ATWOOD, KS *2 Hyd Remotes Required – The WLS1050 Must Be Added If Tractor Only Has One Set Of Remotes. Also, Recommended For Improved Feathering Control On Smaller Tractors, Valve Is Close Center. Specs Features Grinding Time Chart Optional Hand Control Manuals Teeth 3P34 Stump Grinders The 3P34 PTO stump grinder is designed for tractors equipped with a 50–80 horse power motor allowing you to grind into stumps with a 34″ Rotor carrying 54 replaceable carbide teeth. The rugged gear box takes up to 80 HP and develops 803 ft/lbs of stump destroying torque. Designed for Cat 2 3PH and 540 PTO this versatile stump grinder has a cutting depth of 25″ above ground and 14″ below ground. With direct drive from the engine, all the way through the heavy duty gear box to the teeth, a stump grinder on the PTO of a tractor is the most efficient way to use a stump grinder for lawn care or fence row clearing. Model No. 1P14 1P24 3P24 3P34 3P40 Recommended HP Size 20-45 20-45 25-55 45-80 60-120 Maximum Engine HP 45 50 58 85 125 Maximum PTO HP 35 40 50 75 115 Transmission Hydrostatic only Hydrostatic only Any Any Any Hydraulic GPM — — 5–20 5–20 5–20 Rotor Size 16″ 24″ 24″ 34″ 34″ Number of Teeth 12 34 34 52 52 Tooth Part number H3000 S1000 S1000 S1000 S1000 Tooth Construction High speed round tooth Carbide steel bolt-in Carbide steel bolt-in Carbide steel bolt-in Carbide steel bolt-in Cutting Wheel Speed 540 RPM 540 RPM 810 RPM 810 RPM 1000 RPM Cutting Height – Above Ground 10″ 10″ 18″ 25″ 25″ Cutting Depth – Below Ground 5″ 6″ 8″ 14″ 14″ Maximum Cutting Depth – Per Pass 2″ 5″ 6″ 9″ 9″ Maximum Horizontal Cut 18″ 22″ 22″ 32″ 32″ Swing Arc 0° 0° 65° 65° 65° Hub Torque 664 Ft.-Lbs. 885 Ft.-Lbs. 885 Ft.-Lbs. 1475 Ft.-Lbs. 1327 Ft.-Lbs. Over Torque Protection Slip clutch Slip clutch Slip clutch Slip clutch Slip clutch Hitch Cat I Cat I Cat I or II Cat II Cat II Quick hitch compatibility Yes Yes No No No No. of Remotes Required – Hydraulic 0 0 1 or 2 1 or 2 1 or 2 Requires 12 Volt DC No No No No No Input Speed 540 540 540 540 1000 Unit Weight (Shipping) Lbs. 360 450 920 1231 1280 Width (Shipping) 36″ 36″ 42″ 48″ 48″ Length (Shipping) 30″ 30″ 49″ 54″ 54″ FLOW CONTROL FLOW CONTROL Fine tune the performance of your Stump Blaster easily with the Flow Control knob. The Flow Control allows you to adjust the cutting pass speed, to match the size and performance of your tractor. This gives you the smoothest cut possible and with the full return back to the start position, the quickest overall stump grinding time possible. GEARBOX GEARBOX The rugged gear box transfers power from the tractor’s PTO to the rotor creating 803 Ft.-Lbs of torque and turning the rotor and hungry teeth at 810 RPM. CARBIDE TIPPED CARBIDE TIPPED Like the finest saw blades, the cutting teeth on Stump Blasters are carbide tipped. This incredibly hard material ensures reliable cutting performance. When grinding stumps, buried hazards are inevitable; gravel, stones even metal posts are not uncommon to “find”. Our carbide teeth are designed to stand up to this abuse and keep on blasting stumps to dust. MORE TEETH MORE TEETH Many hands make light work, or in this case fine mulch faster and easier. The high number of teeth means that each tooth does less work. Each of the Stump Blasters teeth only need to make a small cut, because the work is shared by more of these rugged teeth, which last longer and typically only need 2 or 3 replaced at a time. The bolt-on designed teeth allow for straightforward replacement. ROTOR ROTOR The massive ¾” thick steel rotor provides the back bone for the Stump Blaster cutting system. It’s the anchor for the carbide tipped teeth. For smooth operation it’s important that the rotor remains solid, with no flexing. The rugged rotor also provides the Stump Blaster with the extra momentum needed when the grinding is tough, making sure the Stump Blaster can power through the hardest stumps. MORE CLEARANCE MORE CLEARANCE The Stump Blaster’s carbide teeth extend a full 1-¼ inches from the rotor. This prevents chips and mulch from getting plugged. More chip clearing produces smoother operation and reduces heat build-up that can damage the rotor and cause premature tooth failure. STABILIZER BASE STABILIZER BASE The heavy duty base provides a solid base for grinding. This allows for more consistent grinding performance and reduces the stress on your tractor. FLOATING DEFLECTOR FLOATING DEFLECTOR The deflector floats as you grind providing chip and debris control from first cut to maximum depth without getting in the way. In tight grinding situations the deflector can be flipped up out of the way. SWING & LIFT CYLINDERS SWING & LIFT CYLINDERS Get right to grinding with less maneuvering of your tractor and less damage to the grass. The swing cylinder gives the operator a 65 degree grinding range without moving the tractor. The lift cylinder allows you to raise and lower the grinding head to get in start position as well as lowering the head after a pass so you’re ready for the next bite. HARDENED STEEL BUSHING HARDENED STEEL BUSHING Spring Bushings made from high grade chrome-vanadium AISI 6150 spring steel on all main pivot points. GREASEABLE PINS GREASEABLE PINS Our grease pins are zinc plated to prevent corrosion which will allow for smoother operation of the units joints over their lifetime. WLS1050 Baumalight Hyd Valve Kit | For Tractors With Only One Set Of Remotes | Add $550 If Shipped Later $ 1,018.00 Add to List Owner’s Manual Baumalight 3P Series Stump Grinder Owner’s Manual Parts Breakdown WLD001627 Baumalight 24-Pack Of S1000 Teeth | 5/8″ Thread – 3/4″ Square $ 540.00 Add to List WLD001773 Baumalight 5/8″ Fine Stover Lock Nut $ 7.50 Add to List WLD002121 Baumalight 52 Pack Of D001773 5/8″ Fine Stover Lock Nuts $ 380.00 Add to List WLD002924 Baumalight Tooth Holder Block For S1000 Tooth (Weld-In) $ 6.00 Add to List WLS1000 Baumalight Stump Grinder Tooth (EACH) | 5/8″ Thread – 3/4″ Square $ 27.00 Add to List

PTO stump grinder designed for tractors equipped with a 50–80 HP motor, with 34″ Rotor carrying 54 replaceable carbide teeth.